How to check if there is any air leakage in the air intake system? An air flow meter can be used to measure the amount of air intake of the fuel injection system, as long as it is in the air flow meter after the intake pipe if there is a case of air leakage, then it will directly affect the intake air to measure Accurate, it will make the mixer thin. The occurrence of a relatively serious leak has directly caused the engine of the green sprinkler to fail to start. During the inspection process, it should be carefully observed whether the air intake hose at the rear of the air flow meter has ruptured, whether the clamps between each joint are loosened, and whether the resonant cavity is cracked. Whether the crankcase ventilation hose is connected or not. In addition, the recovery system for fuel evaporation and the exhaust gas will not be operated in the circulatory system when it is idling or is started. If it is due to other reasons, it will enter the operating state when it is started. Next, it will directly affect the start-up performance. If the exhaust is blocked in the circulation system pipeline or after the fuel evaporation recovery hose is blocked, the engine of the sprinkler will be started. If this happens, the engine can still start normally, which proves that the system is still If you have a fault, you should carefully check it again.
When performing the spark plug inspection of the green sprinkler , if the spark plug gap is too large, it will also affect the start-up performance. The standard gap of the Dongfeng 140 Green Sprinkler Spark Plug should be 0.8 mm. There are some relatively high-energy electronic systems. The gap of the spark plug will also be relatively large, reaching 1.2 mm. If the gap of the spark plug is too large, then it should be based on the use of its own sprinkler model to maintain the standard value of the manual above to make appropriate adjustments.
When the green sprinkler is inspecting the high-pressure sparks, it is necessary to check whether the high-pressure spark above the distributor's high-voltage bus is within the normal range. The green sprinkler also needs to check whether the high-pressure sparks of each cylinder are also normal. In the range. If the spark of the bus is too weak, then the high-voltage coil needs to be replaced. If the spark of the bus is normal and the spark of the sub-line has a broken fire and the spark is relatively weak, then it proves that the distributor cover or It is the case that there is a leakage of electricity in the distribution fire. It should be replaced immediately.
The trends of the Metal Scrap recycling industry
Recycled scrap consists of 58% of post-consumer products that are considered to be obsolete or outdated. 24% of this material is prompt scrap, which is produced in manufacturing plants that create steel. 18% of the industry involves home scrap, which is produced by current operations.
Steel and aluminum can be infinitely recycled. Scrap metal consists of ferrous metals or nonferrous metals. Large items such as cars, dishwashers, washing machines, stoves, and refrigerators are generally created from metal and therefore the best items to recycle.
By baling the products, the volume of metal scrap is greatly reduced, often up to seventy-five per cent.
By reducing the volume in this way, the smelting costs are reduced. In addition, the overall process of recycling and re-casting can be done more quickly.
Manual Metal balers are economically and environmentally beneficial in reducing metal waste. They lower costs, are space-efficient and make transporting the materials much easier.
The Manual Metal Baling press makes your metal recycling more efficient and profitable.
The Y81 series Manual Waste Metal Scrap Baler could not only press all non-ferrous metals such as copper, brass, and aluminium can be recycled as well as ferrous metals from steel to stainless steel, with various sizes for option, high-density compression, compact and strong. Low energy consumption but fast production rate.
Y81 series hydraulic metal baler mainly include the following models.
Y81F (side turn discharge ), Y81T (side push discharge), Y81Q (front push discharge) and Y81S (Double main press ).
We also support the design and manufacture of other model versions upon request.
Y81Q-Manual operation (Front push discharge )
Y81F-Manual operation (Side turn discharge )
Y81F-Semi-automatic operation (Side turn discharge )
Y81T-Semi-automatic operation (Side push discharge )
Y81S-Semi-automatic operation (Double main press discharge )
We provide a variety of models of the hydraulic metal baler, With new technologies to raise the quality and reduce the price, which supports 24 hours fully automatic working environment.
YMSRECYCLING offer economical and effective solutions to help you to process different metal scraps.
The Metal Baling Press can be customized and extended according to the actual needs of your on-site.
CONTACT YMSRECYCLING
Call us now on +86-15950122559
To start maximising your returns from your metal scrap recycling.
Please email sales@ymsrecycling.com or visit our website directly for further information about the products you are interested in.
Manual Metal Baler,Manual Waste Metal Baler,Manual Metal Baling Press,Manual Metal Recycling Baler
Jiangyin Yimaisheng Hydraulic Machinery Co., Ltd. , https://www.ymsrecycling.com