The spindle of the machine tool is moved in the proper position

The machine does not operate normally after the encoder's backup battery is exhausted and the encoder's backup battery is powered down or lost. In this case, it is necessary to re-set the reference point or the origin to correct the coaxiality. The spindle of the machine tool is moved to the proper position so that the spindle of the machine tool is coaxial with the corresponding drill sleeve. That is to find the position of the workpiece processing part. The method of correcting the coaxiality will be connected to the M port of the machine as follows. In this mode, the corresponding axis mode can be selected to jog the machine, and the speed of the jog machine can be adjusted by the magnification. Insert the special measuring tool with the head or the insert into the inner hole of the spindle. The inserted part of the tool must be matched with the inner hole of the spindle or the corresponding axis of the handwheel to adjust the position of the machine to make the probe slowly advance. In the human drill mold, stop the attention after entering the appropriate depth to avoid the probe being in contact with the equipment in the place where the drill is corroded or worn. Then slowly rotate the spindle one or a few times, and record the swing of the lower needle (for horizontal machine tools, there are four positions of up and down, left and right, for vertical machine tools, there are four positions in front, back, left and right), if coaxiality If the coaxiality is not within the required range, refer to the static accuracy of the machine tool. According to the swing condition, jog the corresponding axis of the machine tool and re-adjust the position of the machine tool until the coaxiality meets the requirements, that is, the position of the workpiece is in accordance with the position. At this point, the coaxiality is corrected. From the above conditions and the machining program, the center coordinate of the hydraulic tappet hole of the coordinate is the center of the hydraulic tappet hole. Connect the button on the operation panel, and then press the soft key to display the screen, the parameter can be rewritten at this time. Calling the parameters will disconnect the machine from the position and position according to the information prompt, then re-open the machine power and return to the reference point. The reference point found at this time may not meet the requirements of the position of the workpiece. Move the machine tool to one or know from the above-mentioned known conditions. When the machine tool is at this position, the data of the coordinate axis in the program is the position or position. Use the above method of finding the coaxiality to find the coaxiality, and record the coordinate data at this time. Use one coordinate data to move the machine back to the coordinate data. If an overtravel alarm occurs during the movement, modify the data of the corresponding axis of the parameter to eliminate the overtravel alarm. (Finish)

Mast Lift

Mast lift is widely applicable to the high-altitude operation in the halls and factories of star rated hotels, large supermarkets and other industries. It has the advantages of lifting balance and easy operation. It can enter the general entrance hall, and can enter and exit the elevator at will, with less power consumption, no pollution, and no damage to the ground during work. It can be used for wall work and out work, without dead angle. Single column aluminum alloy electric elevator with gantry span accessories is very suitable for the maintenance of cinemas, auditoriums, churches, etc. The gantry span is easy to assemble, labor-saving in operation and flexible in movement. It can span fixed seats and other obstacles with a height of 1.1m, and can work stably on the steps. Made of high-strength rectangular steel pipe, with good rigidity and stability. Equipped with universal casters, flexible. The span of both ends is adjustable, which can be applied to the requirements of crossing different obstacles. The two end frames are vertically adjustable and can be used for operation on a slope or step with a certain slope. The new generation of products with brand-new design are made of high-strength aluminum profiles. Due to the high strength of the profiles, the deflection and swing of the lifting platform are extremely small. Double mast column structure is adopted, with large load capacity, large platform area, excellent stability, flexible operation and convenient implementation. Its lightweight appearance can give full play to the highest lifting capacity in a small space. The elevator is widely used in factories, hotels, buildings, shopping malls, stations, airports, stadiums, etc. It can be used for installation and maintenance of power lines, lighting appliances, overhead pipelines, and high-altitude cleaning.

Mast Lift,Lightweight Personnel Lifts,Vertical Mast Lifts,Push Around Vertical Mast Lifts

zhongcan machinery Co.,Ltd , https://www.zclift.com