Hardware knowledge: The quality of aluminum depends on four factors.
Alloying element
Alloy 6063 is an alloy prepared with aluminum, magnesium and silicon as the main elements. Each element has a certain range of content, and the price of magnesium is high. In order to reduce the cost, some manufacturers have reduced the amount of magnesium used to a minimum. In some cases, the content of magnesium is lower than the minimum allowable content. Some factories add waste wires and waste pot aluminum waste pots to alloys, basically no 6063 alloy. As a result, the mechanical strength of the aluminum profiles is very low, and it can be as low as bending with two hands and one bend, and is commonly referred to as soft as noodles. This is one of the reasons why aluminum can be a few thousand dollars cheaper.
Regular aluminum manufacturers have internal standards when formulating alloy components, that is, within the range of various elemental contents, each factory has its own smaller range of variation, and the ratio between aluminum, magnesium and silicon is very strict. Each plant has its own data and is confidential. Qualified formula-made alloys can guarantee the quality. Otherwise, the quality will not increase.
2. Aluminum alloy melting furnace
How to melt the 6063 alloy with a good, what stove, which is also of utmost importance, now the furnace used in the country has the level of the 40s, but also the level of the 90s, the worst manufacturers use the original helium boiler. There are coal-fired, oil-burned, gas-fired and electrically heated smelting furnaces. Some stoves have chimneys, and some have no chimneys. The most commonly used are square-shaped furnaces (rectangular furnaces), advanced circular furnaces, and some circular furnaces can tilt aluminum water. On the tonnage of one ton, two tons, five tons, ten tons, twenty-five tons and fifty tons of aluminum melting furnace. More advanced, in the melting furnace below plus a static furnace, static furnace 6063 alloy used in the preparation of important, in this furnace degassing degassing, standing, and then cast aluminum rod for extrusion use. The quality of the alloys formulated in the original coal-burning furnace and the modern circular furnace is absolutely different. In general furnaces, no matter what kind of fuel is burned, there should be a chimney, and most of the waste gas generated during the combustion of fuel can be discharged from the chimney. If the smokeless exhaust gas slag is completely melted in the aluminum water, the aluminum rod used for extrusion is cast, and there are serious slag inclusion bubbles inside. This is one of the reasons for the inferior quality of the aluminum material, which is also one of the reasons for the low price of aluminum.
3. Alloy casting
The level of domestic foundry equipment is also very different. The oldest casting equipment in the country is the iron mold casting in the 40s, and the advanced hydraulic semi-continuous casting. Iron die casting rods have poor crystal structure, and there are a lot of slag inclusions and bubbles in the casting rods. The quality of the casting rods is very poor. Nowadays, the most common ones used in factories are horizontal casting (also known as continuous casting) and semi-continuous casting. Most semi-continuous casting wire rope drive, the best hydraulic transmission. Semi-continuous casting rods vary in length from 3 meters to 4 meters up to 8 meters. Semi-continuous casting is a pit type, which drops on one side of the casting and is cooled on all four sides with cold water. Since the water cooling is evenly distributed around, the casting rod has a uniform crystal structure. However, the downward driving of the wire rope is not as smooth as the hydraulic transmission. The cast rod surface of the hydraulic casting is smoother than the surface of the other cast rods. The smooth surface of the cast rod is one of the prerequisites for the extrusion of the profile. Casting rods with other methods is relatively rough surface, in order to ensure the quality of the profile, sometimes the cast rod first car, the car to cast rod rough appearance. The commonly used semi-continuous casting molds are advanced, hot-top horizontal casting molds. The characteristics of such casting molds can cast a few to several dozen roots at a time, and the casting quality is good. High quality 6063 aluminum alloy casting rods are available. In order to produce good aluminum profiles, it is impossible to produce good aluminum profiles if it is impossible to cast good cast rods using the old and outdated casting equipment. There are many aluminum factories in China. There are no equipments for producing aluminum rods. Instead, 6063 alloy rods are purchased from electric aluminum plants or other factories. Such aluminum plants have the quality of aluminum materials in the hands of the production and casting rod factories, and produce aluminum. Wood is difficult to achieve stable quality. With backward equipment than with advanced casting equipment, the first is a small investment, low production costs, which is why one of the reasons for the big difference in sales of aluminum.
Alloying element
Alloy 6063 is an alloy prepared with aluminum, magnesium and silicon as the main elements. Each element has a certain range of content, and the price of magnesium is high. In order to reduce the cost, some manufacturers have reduced the amount of magnesium used to a minimum. In some cases, the content of magnesium is lower than the minimum allowable content. Some factories add waste wires and waste pot aluminum waste pots to alloys, basically no 6063 alloy. As a result, the mechanical strength of the aluminum profiles is very low, and it can be as low as bending with two hands and one bend, and is commonly referred to as soft as noodles. This is one of the reasons why aluminum can be a few thousand dollars cheaper.
Regular aluminum manufacturers have internal standards when formulating alloy components, that is, within the range of various elemental contents, each factory has its own smaller range of variation, and the ratio between aluminum, magnesium and silicon is very strict. Each plant has its own data and is confidential. Qualified formula-made alloys can guarantee the quality. Otherwise, the quality will not increase.
2. Aluminum alloy melting furnace
How to melt the 6063 alloy with a good, what stove, which is also of utmost importance, now the furnace used in the country has the level of the 40s, but also the level of the 90s, the worst manufacturers use the original helium boiler. There are coal-fired, oil-burned, gas-fired and electrically heated smelting furnaces. Some stoves have chimneys, and some have no chimneys. The most commonly used are square-shaped furnaces (rectangular furnaces), advanced circular furnaces, and some circular furnaces can tilt aluminum water. On the tonnage of one ton, two tons, five tons, ten tons, twenty-five tons and fifty tons of aluminum melting furnace. More advanced, in the melting furnace below plus a static furnace, static furnace 6063 alloy used in the preparation of important, in this furnace degassing degassing, standing, and then cast aluminum rod for extrusion use. The quality of the alloys formulated in the original coal-burning furnace and the modern circular furnace is absolutely different. In general furnaces, no matter what kind of fuel is burned, there should be a chimney, and most of the waste gas generated during the combustion of fuel can be discharged from the chimney. If the smokeless exhaust gas slag is completely melted in the aluminum water, the aluminum rod used for extrusion is cast, and there are serious slag inclusion bubbles inside. This is one of the reasons for the inferior quality of the aluminum material, which is also one of the reasons for the low price of aluminum.
3. Alloy casting
The level of domestic foundry equipment is also very different. The oldest casting equipment in the country is the iron mold casting in the 40s, and the advanced hydraulic semi-continuous casting. Iron die casting rods have poor crystal structure, and there are a lot of slag inclusions and bubbles in the casting rods. The quality of the casting rods is very poor. Nowadays, the most common ones used in factories are horizontal casting (also known as continuous casting) and semi-continuous casting. Most semi-continuous casting wire rope drive, the best hydraulic transmission. Semi-continuous casting rods vary in length from 3 meters to 4 meters up to 8 meters. Semi-continuous casting is a pit type, which drops on one side of the casting and is cooled on all four sides with cold water. Since the water cooling is evenly distributed around, the casting rod has a uniform crystal structure. However, the downward driving of the wire rope is not as smooth as the hydraulic transmission. The cast rod surface of the hydraulic casting is smoother than the surface of the other cast rods. The smooth surface of the cast rod is one of the prerequisites for the extrusion of the profile. Casting rods with other methods is relatively rough surface, in order to ensure the quality of the profile, sometimes the cast rod first car, the car to cast rod rough appearance. The commonly used semi-continuous casting molds are advanced, hot-top horizontal casting molds. The characteristics of such casting molds can cast a few to several dozen roots at a time, and the casting quality is good. High quality 6063 aluminum alloy casting rods are available. In order to produce good aluminum profiles, it is impossible to produce good aluminum profiles if it is impossible to cast good cast rods using the old and outdated casting equipment. There are many aluminum factories in China. There are no equipments for producing aluminum rods. Instead, 6063 alloy rods are purchased from electric aluminum plants or other factories. Such aluminum plants have the quality of aluminum materials in the hands of the production and casting rod factories, and produce aluminum. Wood is difficult to achieve stable quality. With backward equipment than with advanced casting equipment, the first is a small investment, low production costs, which is why one of the reasons for the big difference in sales of aluminum.
Flower Sleeve,Flower Bouquet Sleeves,Sleeve Flowers,Cellophane Flower Sleeves
SHANGHAI WELLONG IMPORT AND EXPORT CO., LTD , https://www.chinafloralfoam.com