The SG-2 vibration speed sensor SDJ-2G-2S is mainly installed on the bearing caps of various rotating machinery (such as steam turbines, compressors, fans and pumps). It is an electromagnetic sensor that cuts magnetic lines by a moving coil and outputs a voltage. Therefore, it does not require power supply during operation and is easy to install.
1. Measuring range: Frequency: 10 ~ 300Hz
Amplitude: 0 to 200um 0 to 500um 0 to 800um (peak to peak)
Intensity: 0 ~ 20mm / s 0 ~ 25mm / s 0 ~ 50mm / s (true RMS)
2. Measurement accuracy: ±0.5, linear error ≤1%FS
3. Measurement method: vertical or horizontal
4. Output signal: current output: 4 ~ 20mA (load ≤ 1KΩ)
5. Ambient temperature: -10 ~ 65 ° C (relative humidity ≤ 85%)
6. Power supply voltage: DC24V (power consumption ≤ 3W)
7. Dimensions: 35 × 75 (mm)
8. Fixed screw hole: M10×1.5×10mm
ST-2G vibration sensor sensitivity 20-50mv/mms
Second, the basic principles
The basic principle of the CD-21 series speed sensor is based on an inertial mass (coil assembly) and a housing in which a magnet is fixed. When the inertial mass is suspended from the housing by the elastic element, the sensor housing is fixed to the vibrating body. Above, this
SG-2 Vibration Speed ​​Sensor The vibration speed sensor is usually used to measure the vibration of the bearing and, in a few cases, to measure the vibration of the shaft. When measuring the vibration speed, if the sensor is installed incorrectly or the installation is not strong, the measurement result may be distorted or the sensor may be damaged due to vibration. Therefore, we must carefully choose the installation method of the vibration speed sensor. The vibration sensor is used together with the vibration monitor to achieve continuous long-term monitoring and is suitable for measurement of mechanical vibrations such as steam turbines, fans, pumps, and coal mills. The working principle is based on a primary component that converts mechanical energy into electrical energy. It is fixed on the bracket by two coils, and a piece of magnetic steel is connected to the casing through the piece, and the magnetic steel moves in the line. The magnetic lines of force are cut, thus generating an induced electromotive force. The voltage is proportional to the speed of the casing, which is called the vibration speed sensor. The vibration sensor produced by Zhengzhou Hangke has small volume, good sealing and long service life. Due to the double coil structure, it can superimpose the effective signals, and the interference signal attenuation effectively improves the anti-interference ability.
SG-2 vibration speed sensor SDJ-2G-2S
Integrated vibration and temperature transmitter KL-ZDW86-60-A
Integrated vibration and temperature transmitter KL-ZDW86-40-A
HZD-L-A2-B2-C2-D2-E2 vibration intensity monitoring and protection device
TRA-2X intelligent travel monitoring and protection device
Thermal expansion monitor ZT6501
Vibration Monitoring and Protection Instrument SDJ-3B
Vibration monitoring and protection device HZD-D/S-2
SDJ-3BS, SDJ-3LS type vibration monitoring and protection device
SDJ-6N vibration monitoring and protection instrument (intelligent)
SDJ-6L vibration monitoring and protection device
SDJ-3L vibration monitoring and protection device
CDX-2 vibration monitor
CDX-2A vibration intensity monitor
ZDX-N type shaft vibration monitor
XDZW-2 axial displacement monitoring and protection device
XDZC-2 type expansion monitoring and protection device
YDJ-A oil motive monitor
YDJ-Y type fuel tank oil level monitoring and protection device
1. Measuring range: Frequency: 10 ~ 300Hz
Amplitude: 0 to 200um 0 to 500um 0 to 800um (peak to peak)
Intensity: 0 ~ 20mm / s 0 ~ 25mm / s 0 ~ 50mm / s (true RMS)
2. Measurement accuracy: ±0.5, linear error ≤1%FS
3. Measurement method: vertical or horizontal
4. Output signal: current output: 4 ~ 20mA (load ≤ 1KΩ)
5. Ambient temperature: -10 ~ 65 ° C (relative humidity ≤ 85%)
6. Power supply voltage: DC24V (power consumption ≤ 3W)
7. Dimensions: 35 × 75 (mm)
8. Fixed screw hole: M10×1.5×10mm
ST-2G vibration sensor sensitivity 20-50mv/mms
Second, the basic principles
The basic principle of the CD-21 series speed sensor is based on an inertial mass (coil assembly) and a housing in which a magnet is fixed. When the inertial mass is suspended from the housing by the elastic element, the sensor housing is fixed to the vibrating body. Above, this
SG-2 Vibration Speed ​​Sensor The vibration speed sensor is usually used to measure the vibration of the bearing and, in a few cases, to measure the vibration of the shaft. When measuring the vibration speed, if the sensor is installed incorrectly or the installation is not strong, the measurement result may be distorted or the sensor may be damaged due to vibration. Therefore, we must carefully choose the installation method of the vibration speed sensor. The vibration sensor is used together with the vibration monitor to achieve continuous long-term monitoring and is suitable for measurement of mechanical vibrations such as steam turbines, fans, pumps, and coal mills. The working principle is based on a primary component that converts mechanical energy into electrical energy. It is fixed on the bracket by two coils, and a piece of magnetic steel is connected to the casing through the piece, and the magnetic steel moves in the line. The magnetic lines of force are cut, thus generating an induced electromotive force. The voltage is proportional to the speed of the casing, which is called the vibration speed sensor. The vibration sensor produced by Zhengzhou Hangke has small volume, good sealing and long service life. Due to the double coil structure, it can superimpose the effective signals, and the interference signal attenuation effectively improves the anti-interference ability.
SG-2 vibration speed sensor SDJ-2G-2S
Integrated vibration and temperature transmitter KL-ZDW86-60-A
Integrated vibration and temperature transmitter KL-ZDW86-40-A
HZD-L-A2-B2-C2-D2-E2 vibration intensity monitoring and protection device
TRA-2X intelligent travel monitoring and protection device
Thermal expansion monitor ZT6501
Vibration Monitoring and Protection Instrument SDJ-3B
Vibration monitoring and protection device HZD-D/S-2
SDJ-3BS, SDJ-3LS type vibration monitoring and protection device
SDJ-6N vibration monitoring and protection instrument (intelligent)
SDJ-6L vibration monitoring and protection device
SDJ-3L vibration monitoring and protection device
CDX-2 vibration monitor
CDX-2A vibration intensity monitor
ZDX-N type shaft vibration monitor
XDZW-2 axial displacement monitoring and protection device
XDZC-2 type expansion monitoring and protection device
YDJ-A oil motive monitor
YDJ-Y type fuel tank oil level monitoring and protection device
Fixed Telescopic Belt Conveyor
Fixed Telescopic Belt Conveyor can be widely used in airport baggage handling systems, mail and parcel handling centers, factory manufacturing, retail distribution centers, food processing and packaging, cement factories, fertilizer factories, salt factories, furniture, brick factories nationwide Wait. The conveyor equipment produced by Keke is suitable for a wide range of products, from electronic products to refrigerators, etc.
Fixed Telescopic Belt Conveyor,Fixed Telescopic Conveyor,Customized Fixed Telescopic Belt Conveyor,Telescopic Conveyors
DMT Machineries (Suzhou) Ltd , https://www.dmtsz.com