1. Vibration eliminators are designed for installation in the suction and discharge lines of Air conditioning and Refrigeration system to dampen the transmission of compressor-induced vibration through system piping.
2. Each unit is constructed of a deep pitch corrugated tubing for increased flexibility and vibration absorption, covered by a high tensile wire braid for superior strength.
3. Tubing and braid are reinforced by ferrules at each end and connected to female copper tube ends by a high temperature braze alloy.Â
4. Each unit securely brazed, pressure and vacuum tested, cleaned, dehydrated and sealed in plastic wrap
5. Stainless steel corrugated tubing and high tensile wire braid
6. Compatible with all HFC, HCFC and CFC refrigerants including R410A refrigerant
7. UL approved and CE marked under the Pressure Equipment Directive(PED) 97/23/EC
8. Available with Stainless steel tube ends for use with Ammonia NH3Â
Â
Model |
Dimensions ( inch ) |
Working Pressure(psig) |
Burst Pressure(psig) |
|||||
A |
B |
C |
D |
E |
||||
VA-014 |
1/4" |
1/2" |
6-1/2" |
7-7/8" |
200mm |
1/2" |
650 |
3250 |
VA-038 |
3/8" |
3/4" |
7" |
8-1/2" |
217mm |
1/2" |
650 |
3250 |
VA-012 |
1/2" |
7/8" |
7-1/4" |
9" |
228mm |
1/2" |
650 |
3250 |
VA-058 |
5/8" |
15/16" |
8" |
9-7/8" |
250mm |
7/8" |
650 |
3250 |
VA-034 |
3/4" |
1/4" |
8-1/16" |
10-1/2" |
268mm |
7/8" |
650 |
3250 |
VA-078 |
7/8" |
1-3/8" |
9-1/4" |
12" |
305mm |
7/8" |
650 |
3250 |
VA-100 |
1" |
1-3/4" |
9-7/16" |
13" |
332mm |
7/8" |
650 |
3250 |
VA-118 |
1-1/8" |
1-3/4" |
9-7/16" |
13" |
332mm |
7/8" |
650 |
3250 |
VA-138 |
1-3/8" |
2-1/16" |
11-7/16" |
15-1/2" |
395mm |
7/8" |
550 |
2750 |
VA-158 |
1-5/8" |
2-1/4" |
12-3/8" |
16-15/16" |
429mm |
1" |
510 |
2550 |
VA-218 |
2-1/8" |
2-11/16" |
15-3/16" |
20-1/2" |
524mm |
1-3/8" |
400 |
2000 |
VA-258 |
2-5/8" |
3-1/16" |
18" |
24-1/8" |
617mm |
2" |
350 |
1750 |
VA-318 |
3-1/8" |
3-7/16" |
20" |
26-15/16" |
684mm |
2" |
320 |
1600 |
VA-358 |
3-5/8" |
4-1/16" |
24" |
32-1/8" |
818mm |
2" |
190 |
570 |
VA-418 |
4- 1/8" |
4-1/2" |
24" |
33" |
836mm |
2" |
190 |
570 |
Â
CHARACTERISTICSÂ Â
Â
1. Suitable for a wide range of the tail pipe link.
2. We  can make parts with a high degree of flexibility.Â
3. In particular, we increase the height of the bellows to enhance the
effectiveness of vibration absorption.Â
4. This product is used in exhaust system and high-and low-temperature.
5. It can decrease engine noise and vibration.
Â
Glass Microfiber Filter Paper of ASHRAE Grade(F6-F9)
Glass Microfiber Filter Media For Air ASHRAE FILTER :F6-F9
ASHRAE fiberglass filter media are comprised primarily of glass microfibers and are produced with a wet laid process similar to those used for the production of paper. It's an ideal raw material to produce air filters. It's efficiency ranges from F6-F9 with low pressure drop and good strength.
Fiberglass F9 Air Filter Paper,Fiberglass F8 Air Filter Paper,Fiberglass F7 Air Filter Paper,Fiberglass F6 Air Filter Paper,
ASHRAE :
Grade: F9 F8 F7 F6
Efficiency(≥%): 95 90 80 60
Basic Weight (+-5g/m2) : 70 70 70 70
Thickness (±0.02mm@100kpa ) : 0.34 0.34 0.34 0.33
Air Resistance Pa @5.3cm/s: 88 35 33 20
Tensile Strength 1200 1200 1200 1200
Stiffness: 1200 1200 1200 1200
ASHRAE grades (F6-F9): ordinary air-conditioning system, gas turbine air intake, air compressor, etc.
Micro Fiberglass Filter Paper,Fiberglass F8 Air Filter Paper,Ashrae Fiberglass Filter Media,F6 Glass Microfiber Filter Paper
Hebei Fangyu Trade Co., Ltd. , https://www.fangyu-filtermedia.com