Air compressor unit cooling water automatic circulation device Shuaikang Electric Co., Ltd. Equipment Department Zhejiang Yuyao City Lishan Shuaikang Industrial Park 491,05746224 The company's early two 3-port / 8 air compressor cooling water is in-line type, annual water fee About 43,000 yuan, a huge waste. To this end, a set of secondary circuit water circulation cooling device is designed, the effect is very good, the annual savings can be about 36,000 yuan 6 minus the electricity expenses 6 see Figure 1, when the air compressor unit is turned on, the valve port 7, 10 is closed. In the case, the water in the high water tank passes through 8, 20, 5 to the multi-way inlet end of the air compressor and the aftercooler, and the discharged cooling water flows to the well 15 through the ditch, and the self-priming 14 is based on the water level of the high water tank 12. The high and low intermittent water is automatically pumped to the water inlet end of the cooling tower 13, and the water cooled by the cooling tower is discharged into the water tank to form a circulation. If the summer heat requires a large flow of cooling, open the pipe to make the water pressure high and the flow rate increase. If you need to repair the water and cooling tower, the air compressor does not need to stop. There are two ways to cool the water, which can be selected as needed.
Is to close the valve port 5, the valve port 7 is open, using the tap water straight volleyball to explain 12. 篼 position water tank 13. Cooling tower 14. Self-priming pro 15. Water well cooling, all water springs, water tanks, cooling towers do not work; The valve port 10 is opened, and the float valve 11 automatically controls the water level of the water tank. The cooling water is from 8, 6, and 5 to the required cooling water inlet end, and the self-priming and cooling towers are not working. When it is necessary to replenish the cooling water during normal work, the valve port 10 can be opened, and the valve can be closed after the water is replenished.
2002 Excellent article selection article title period page number author name and other name of the person selected work stone unit job address zip phone cast iron machine percussion device set special Niu Songlin Linzhou Iron and Steel Co., Ltd. iron-making branch, Henan Yangshi No. 8, Lin Gang Road, Lingyang Town, Linzhou, 61, 037,265, 4771, Classification: 762 Qiao. 6 Document identification code: 6 Lingang Ironmaking Branch has four cast iron machines, and the average daily cast iron is more than 900. 1. The cast iron demoulding is manually assisted, and the labor intensity is large, resulting in serious pig iron mixed number. To this end, a simple tapping device for automatic stripping of the cast iron is designed, which is described below.
The device is shown in Figure 1, and its transmission route is. Motor 1 motor 2 reducer shot 9500 3. Pull rod 4. Rotating plate 5. Bracket 6. Sliding bearing 7. Toggle pin 8. Transmission gear 9. Power transmission shaft 1. Reducer 1285011. Semi-open reducer mouth. Transmission skill beam 13. Chain 14. Chain belt drive wheel 15. Rotating shaft 2. Structural features For the more dispersed multi-way cooling water outlet, the water diversion is used to concentrate the water into the well, and the water well replaces the underground tank, which is convenient and low in cost. At the same time, the groundwater in the well can also act as a hydrating effect. In addition to the automatic control of the water level, the electric control also installs the automatic alarm device with the lowest water level. When the water tank is damaged, the electric bell alarm of the duty room is started when the water level of the high water tank drops to the low limit. This device is especially suitable for the cooling water of several plastic injection molding machines. The capacity of the water, the well and the cooling tower are selected according to the actual flow rate of the cooling water.
500 reducer anus 9850 reducer power transmission shaft rotating shaft rotating disk toggle shaft pin toggle lever transmission beam silver, complete automatic demoulding.
In order to save energy, the tapping device does not have a separate power source. According to the position of the site, the low-speed shaft of the 850 reducer was first modified, and six 8-hole 35 screw holes were evenly distributed on the end face of the low-speed shaft, and the power transmission shaft was installed.
In order to make the tapping device's funny head accurately hit the middle of the iron mold, the diameter of the rotating disc should be the diameter of the caster chain with the driving wheel diameter.
The number of rotating discs and the number of the toggle pins should be coordinated with the speed of the caster chain with the drive wheel. In order to prevent the wear of the toggle pin from being accelerated and frequently replaced, a wear-resistant steel sleeve is mounted on the toggle pin.
The steel bracket, the transmission beam, the toggle lever, and the Jianying are made and installed on the spot. The suitable angle of the toggle lever and the handle is 7.~85° from the side. The two bearing housings must be installed in the same plane, and the transmission gears can be combined to ensure the transmission accuracy.
Wu Zongze. Mechanical Parts. Central Guangqiao TV University Press. Qiao 88 Cheng Daxian wait. Mechanical design manual. Chemical Industry Press. 1993 [Received Date] is the implementation of the Standards for Searching and Evaluating Data of Academic Journals in the Press and Publications Department, AJDB/Tl1988. This article is from the 2003 classification number, author and its work unit, author profile, abstract, keywords, Received date, fund items and references.
In order to do this work, I hope that the author can cooperate with the author and his work unit, the author's profile, abstracts, keywords, fund projects and reference texts. In addition, the manuscript should be legible, with appropriate line spacing, and edited.
Special announcement
The role of the beach tent: in outdoor activities it can shelter from the wind and rain, prevent reptiles from entering,
to provide you with a relatively safe small place. Especially in the snow, mountains, and other environmental
vicious environment, more highlight the role of beach tents.
And choosing the right tent for yourself needs to consider factors:
1. the use of the environment.
2. the use of the season
3. the number of people using.
4. personal acceptance of the price.
Nature is a magical world, so consider an outdoor camping trip in your spare time to add a little more color to
your life! If you haven't tried it, you won't feel the other side of nature. Bring your beach tent, Sleeping Bag,
and moisture-proof mat, and go camping! We at Outerlead are passionate about camping products
and welcome your inquiries.
pop up beach tent,beach sun shelter tent,tent for beach,baby beach tent,beach shade tent
Ningbo Autrends International Trade Co., Ltd. , https://www.zjouterlead.com