1 water outlet plug cover 2 water inlet plug cover 3 upper cover 4 cooler core 5 bottom cover 6 leather tube (water) 7 pressure gauge 8 handle 9 hand pump 10 water pipe (water absorption) 11 bucket 12 water copper tube pressure test Figure Information China Building Materials Technology and Equipment Corporation and Japan Asahi Co., Ltd. (AGC) signed an agreement on March 10, 2000 to represent the company's glass refractory bricks for sale in China. AGC is a world-renowned large-scale glass company. It has sold many sets of refractory bricks in China through China Building Materials Technology and Equipment Corporation, such as Tongliao Glass Factory and Lingyuan Glass Factory. The refractory bricks produced by the society have the characteristics of stable and reliable quality, short delivery time and relatively low price.
(Zhang Liping) Treatment Method for Descaling of Air Compressor Cooler Core Liu Yong Jiangsu Glass Group Co., Ltd. (223800) Three 6L-48/5 .75 type non-lubricated air compressors of our company's float nitrogen oxide station operate The cycle is long and the quality of the cooling water used is not so good, so the intercooler and aftercooler cores are often filled with scale, which results in a much reduced cooling effect on the compressed air, especially in summer. Our company has a lot of brains and tried many methods. Here is one of the feasible descaling methods - pickling.
1. Principle of pickling method Since copper is an inactive metal, it hardly reacts in hydrochloric acid solution, but its alloy and oxide can react with hydrochloric acid solution. In order to prevent and reduce this, it is added when preparing hydrochloric acid solution. A proper amount of corrosion inhibitor prevents and slows the solution from corroding the copper tube. The main component of the scale and the hydrochloric acid solution will react rapidly to form a substance dissolved in water, thereby achieving the descaling effect.
2. The pickling process is first formulated with an acid wash solution using 5 hydrochloric acid 0. 08 aniline 0.1 formaldehyde.
Place the cooler core vertically on the flat surface, and then directly inject the prepared acid into each copper tube for 10-20 minutes. Use an iron brush with a diameter slightly smaller than the inner diameter of the copper tube to remove the residue and then pour out the solution from all the copper tubes. Cycle back and forth until the scale is removed. Finally, inject the 0.1% NaOH solution into the copper tube and circulate it twice. After a few minutes, let it go and rinse it off with water.
3. Leak test and pressure test The hand pump shown in the figure below is equipped with a pressure gauge to display the pressure. Press the handle and fill the cooler core until the pressure reaches the required test pressure of 4.5 Kgf/cm 2 for 30 minutes. Check the copper tube for water-free bead leakage. If there is no water seepage, it will be qualified. Otherwise, tube replacement and expansion must be performed.
4. When changing the tube and the expansion tube, when replacing the leaking copper tube, firstly, the copper tube that seeps at the interface is manually expanded by the tube expander. After the expansion, the pressure test leak is performed until the test pressure requirement is met, so that no water leakage occurs.
Our company's three 6L-48/5 .75 non-lubricated air compressors have a total of 12 cooler cores, and at least 4 to 6 demolitions are required each year. According to the current market survey, it is known that a new cooler core is about 7,000 yuan, and it takes only a few tens of dollars to repair a core. The money saved by the descaling repair to the company is considerable. Using the above pickling method, our company has successfully washed the cores of the three coolers, and the effect is very good, which strongly supports the production.
2000 ? 3 ? China Building Materials Equipment Engineers
Aws E316-16 Welding Electrodes
Description:
E316-16 Welding Electrodes deposited metal is a stable austenite structure containing 18Cr-12Ni-2Mo. Due to the Mo element content in it, it shows excellent properties in resisting corrosion of acetic acid, sulphuric acid, phophate acid as well as salt, and has good high temperature crack-resistance.
Both AC and DC can be applied and it can be used for all position welding with excellent welding performances and good mechanical properties.
Applications:
AWS E316-16 Welding Electrodes is suitable for welding the parts of chemical industry and power engineering, such as A1S1 316 Steel, SUS 316 steel etc.
Attention:
1. Before welding, the welding electrodes should be baked at the temperature from 300 to 350 ℃ for one hour.
2. The stainless steel brush must be used to clean the weld seam, in order to avoid iron fillings penetrating there to affect its quality
AWS E316-16 Welding Electrodes
Aws E316-16 Welding Electrodes,316L-16 Welding Electrode,316L-16 Welding Rod,E316-16 Welding Electrodes
Dingzhou Jinlong Metal Production Co., Ltd. , http://www.weldingelectrodefactory.com