The lifting column can be used in a wide range of applications. Whether it is a highway or an airport or a unit entrance or exit, the lifting column can be used to complete vehicle control. The high-strength frame design structure is suitable for airports, power plants, bank entrances and exits, etc. The heavy-duty frame structure is suitable for enterprises, public institutions, parking lots, hospitals, etc., and the light frame structure is suitable for scenic spots, properties, squares and other places. However, the stone pier is only suitable for traffic intersections that do not require lifting, and the range is smaller relative to the lifting column.
The lifting column can be lifted freely. The bottom of the lifting column is equipped with a hydraulic drive system. The power is strong and the system is stable. When the vehicle passes, just press the remote control gently, the lifting column will automatically fall to the ground, and the vehicle will be at this time. It can be passed through, and the lifting column adopts a stainless steel chassis. Even if a large vehicle passes by, it will not cause deformation and bending of the chassis.
The car hits the lifting column, the column blocks the car, the floor panel and the limit flange act as the fulcrum of the force. For the fragile materials such as cast aluminum and cast iron, the fulcrum cannot be made, and the fulcrum must be directly exposed on the embedded pedestal. Pass the strength to the buried foundation to form a solid support point. The bumper flange must be in direct contact with the pre-embedded flange to create piston motion that directly transfers force to the pre-buried and pre-buried foundation to release energy. The lifting column can be used in a wide range of applications. Whether it is a highway or an airport or a unit entrance or exit, the lifting column can be used to complete vehicle control. The high-strength frame design structure is suitable for airports, power plants, bank entrances and exits, etc. The heavy-duty frame structure is suitable for enterprises, public institutions, parking lots, hospitals, etc., and the light frame structure is suitable for scenic spots, properties, squares and other places. However, the stone pier is only suitable for traffic intersections that do not require lifting, and the range is smaller relative to the lifting column.
The lifting column can be lifted freely. The bottom of the lifting column is equipped with a hydraulic drive system. The power is strong and the system is stable. When the vehicle passes, just press the remote control gently, the lifting column will automatically fall to the ground, and the vehicle will be at this time. It can be passed through, and the lifting column adopts a stainless steel chassis. Even if a large vehicle passes by, it will not cause deformation and bending of the chassis.
The car hits the lifting column, the column blocks the car, the floor panel and the limit flange act as the fulcrum of the force. For the fragile materials such as cast aluminum and cast iron, the fulcrum cannot be made, and the fulcrum must be directly exposed on the embedded pedestal. Pass the strength to the buried foundation to form a solid support point. The bumper flange must be in direct contact with the pre-embedded flange to create piston motion that directly transfers force to the pre-buried and pre-buried foundation to release energy. So what are the steps when installing the lifting column?
Step 1: Digging the pit
Foundation pit width: 500mm, foundation pit depth: 1200mm
Step 2: Laying the bottom datum
Laying at the bottom of the foundation pit with bricks. Masonry layer thickness 200mm
Step three:
Laying drainage channels (1): Drainage channels are made of bricks on pre-layed gravel. Drainage width: 100mm, height: 100mm
Laying the drainage channel (2): According to the number of lifting columns, build a layer above the drainage channel to cover the drainage channel to avoid filling the drainage channel when pouring cement.
Step 4: Place the lifting column
After the drains are completed, put them into the lifting column according to the plan and adjust the horizontal angle to ensure that the lifting column is flush with the road surface.
Step 5: Fix the device
After ensuring that the equipment is level with the ground, fill in a small amount of cement to secure the equipment.
Step 6: Equipment wiring
The TV cable uses the RVV3*2.5 specification wire, and the LED warning lamp uses the 4*1.5 specification wire. After connecting the wire, insert the PVC pipe into the control box.
Step 7: Control box wiring
According to the diagram, the control box connection method is connected to the positive and negative lines of the motor and the positive and negative lines of the common line LED light group connected to the lamp group.
Step 8: Debugging
After the control box is connected, conduct a power-on test to ensure that the lift is normal, and the rise and fall are consistent with the direction of the remote control.
Step 9: Backfilling the earth
After the equipment is debugged, fill in the sand and compact it, leaving a distance of 200mm from the ground.
Step 10: Level the ground
Make sure that the lifting column is parallel to the ground to pour cement on the bauxite layer, flush with the ground and restore the road surface.
PVC Edge Banding For Furniture
The main function of the edge banding is to seal the cross-section of the board, so as to avoid the damage of the board and the adverse factors (mainly moisture) in the process of use and prevent the formaldehyde inside the board from volatilizing, and at the same time achieve the effect of beautiful decoration.
The product has the following main features: smooth surface, no blistering, no ribbing, moderate gloss, smooth surface and back surface, uniform thickness, uniform width, reasonable hardness, high elasticity, good quality, strong wear resistance, trimmed and sealed The color of the side and the side is close to the surface color, not whitish, good gloss, and the overall color of the finished furniture is coordinated.
Furniture edge banding is a material for protecting, decorating and beautifying the section of furniture panels. It can make a piece of furniture show the overall effect of clear wood grain and colorful.
PVC furniture edge banding is relatively light, which is relative to metal and plexiglass. The reason for the lightness is not because it is a polymer compound, but because they are organic compounds, which are composed of carbon, hydrogen, oxygen, and chlorine. And other lighter elements.
The material of pvc furniture edge banding is plastic, which is easy to process. Plastic has plasticity, that is, it deforms after heating or pressurizing, and maintains its original shape after the temperature drops or the pressure disappears. It can be processed into edge bands of their respective shapes by extrusion and other methods, such as T-shaped edge bands, H-shaped edge bands, D-shaped edge bands, V-shaped edge bands, I-shapes, and so on.
pvc furniture edge banding is of high quality and low price, and the price of plastic is far less than that of metal.
PVC Edge Banding For Furniture,Pvc Edge Banding For Furniture, Edge Banding For Furniture,Pvc Edge Banding Tape
Henan Shunbang Chemical Industry CO.,Ltd , https://www.sblubricant.com
